bck

ESP32/OLED_ESP32/.vscode/extensions.json

@@ -3,5 +3,8 @@
     // for the documentation about the extensions.json format
     "recommendations": [
         "platformio.platformio-ide"
+    ],
+    "unwantedRecommendations": [
+        "ms-vscode.cpptools-extension-pack"
     ]
 }

ESP32/OLED_ESP32/src/main.cpp

@@ -40,8 +40,11 @@ void loop()
   display.setCursor(0,0);
   display.print("Contador: ");
   display.println(contador++);
+  display.println("");
   display.setTextSize(1);
-  display.println("UNELECTRONICA ESP32");
+  
+  display.println("SEBAS ROBOTICA");
+  display.println("");
   display.setTextSize(2);
   display.print("T: ");
   //tempsensor.waloop_timee(); 

ESP8266/MatrixLedsRGB/.vscode/extensions.json

@@ -3,5 +3,8 @@
     // for the documentation about the extensions.json format
     "recommendations": [
         "platformio.platformio-ide"
+    ],
+    "unwantedRecommendations": [
+        "ms-vscode.cpptools-extension-pack"
     ]
 }

ESP8266/MatrixLedsRGB/platformio.ini

@@ -20,8 +20,8 @@ lib_deps =
 monitor_speed = 115200
 upload_speed = 115200
 monitor_flags = --raw
-upload_protocol = espota
-upload_port = 192.168.1.104
-upload_flags = 
-	--port=8266
-	--auth=un260874
+;upload_protocol = espota
+;upload_port = 192.168.1.9
+;upload_flags = 
+;	--port=8266
+;	--auth=un260874

ESP8266/MatrixLedsRGB/src/main.cpp

@@ -11,8 +11,8 @@
 #endif
 WiFiUDP ntpUDP;
 NTPClient timeClient(ntpUDP, "0.south-america.pool.ntp.org", -18000, 6000);
-const char *ssid = "mdchaparror";
-const char *password = "un260874";
+const char *ssid = "CHAPARRO";
+const char *password = "Un260874";
 long timeAnterior;
 long matrix_time;
 int matrix_speed = 150;
@@ -23,11 +23,16 @@ int matrix_speed = 150;
 
 void setup()
 {
-  Serial.begin(921600);
+  delay(5000);
+  
+  Serial.begin(115200);
+  Serial.println("HOLA");
   WiFi.mode(WIFI_STA);
   WiFi.begin(ssid, password);
+  
   while (WiFi.waitForConnectResult() != WL_CONNECTED)
   {
+    Serial.println("Conectando WIFI");
     delay(5000);
     ESP.restart();
   }

PICO/README.md

@@ -2,11 +2,31 @@
 
 ## Boards
 
-+ RASPBERRY PI PICO
+## RASPBERRY PI PICO
 
-### PinOUT PICO
+#### PinOUT
 ![pinmap](Raspberry-Pi-Pico-pinout-diagram.png)
 
+## RP2040 ZERO
++ RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom.
++ Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz.
++ 264KB of SRAM, and 2MB of on-board Flash memory.
++ USB-C connector, keeps it up to date, easier to use.
++ The castellated module allows soldering direct to carrier boards.
++ USB 1.1 with device and host support.
++ Low-power sleep and dormant modes.
++ Drag-and-drop programming using mass storage over USB.
++ 29 × multi-function GPIO pins (20× via edge pinout, others via solder points).
++ 2 × SPI, 2 × I2C, 2 × UART, 4 × 12-bit ADC, 16 × controllable PWM channels.
++ Accurate clock and timer on-chip.
++ Temperature sensor.
++ Accelerated floating-point libraries on-chip.
++ Programmable I/O (PIO) state machines for custom peripheral support.
+  
+  #### PinOUT
+![pinmap](RP2040-Zero-details.jpg)
+  
+
 ### Data
 + [SDK](data/PICO_C_SDK.pdf)
 + [DATASHEET](data/pico-datasheet.pdf)